Pieco Serwis Gas Furnaces & Foundry Equipment for Sale
Starts: 26 November 2025 at 14:00 GMT
Ends: 15 January 2026 at 14:00 GMT
Short Notice Furnace and Associated Foundry Equipment from GE Power Sp. z o.o. Please see the Essential information section for GE Approved contractors as well as individual lots. NOTE: Vendor to approve all closing bids prior to Apex final invoicing. Any Bidder MUST and CAN ONLY USE the GE-Approved Contractors to Work Onsite.
Share:
Showing 26 of 26 lots
- LOT 4C
![site]()
Heating Gas Enclosure with Front & Pendant Control Roof Doors
Approx Dimensions L11 x W14 x H13m. With Pneumatic Points & Lifting. Approved Contractor for this Lot is Pieco-Budow, Maria Pauuszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 6C
![site]()
Pieco Serwis Gas Furnace 'H' With Control & Loading Bogey
With Movable Bottom (H) Automatic Control With Computer Visualisation. Load Capacity 100 Ton, Hearth Length 9.5m, Gate Clearance Width 7.5m, Height 5m, Maximum Temperature 1,150° C. Temperature. Approved Contractor for this Lot is Pieco-Budow, Maria Paluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 6F
![site]()
Pieco Serwis Gas Furnace 'A' With Control & Loading Bogey
With Movable Bottom (B) Automatic Control With Computer Visualisation. Load Capacity 55 Ton, Hearth Length 8m, Gate Clearance Width 5.2m, Height 4.1m, Temperature 1,100° C. Temperature Dispersion ±10° C. With Extraction. Pieco-Budow, Maria Paluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 4
![site]()
Furnace for Drying and Quenching of Ferrous Metals with Siemens Control & Electrical Cabinet
Approved Contractor for this Lot is Pieco-Budow, Maria Paluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 9
![site]()
Famot Tum-25B Straight Bed Centre Lathe
3 Jaw Chuck. Maximum Swing Over Bed Ø300mm. Maximum Swing Over Cross Slide Ø178mm. Centre Height Distance Between Centres 800mm. Spindle Bore Ø38mm. Speed Range 50-1,500rpm (Motor 3.2kW). Longitudinal Feed Range (9) 0.02-0.4 Position Toolpost. S/No. 1865 (1974). Approved Contractor for this Lot is Pieco-Budow, Maria Pauluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl - LOT 80
![site]()
Mobile Pressure Pot
Ø320 x 330mm Deep. Approved Contractor for this Lot is Promxmus, Artur Azborowski, Tel: 539 629 111, a.zaborowski@proxmus.com If you are the winner of this Lot, please contact Artur Azborowski for a removal quotation. - LOT 81
![site]()
Mobile Pressure Pot
Ø320 x 330mm Deep. Approved Contractor for this Lot is Promxmus, Artur Azborowski, Tel: 539 629 111, a.zaborowski@proxmus.com If you are the winner of this Lot, please contact Artur Azborowski for a removal quotation. - LOT 133
![site]()
Steel Parts Trolley
Approved Contractor for this Lot is Promxmus, Artur Azborowski, Tel: 539 629 111, a.zaborowski@proxmus.com If you are the winner of this Lot, please contact Artur Azborowski for a removal quotation. - LOT 297
![site]()
(3) Assorted Jacks
Comprising: (1) SJ50 Rail Jack, 5000kg Capacity; (1) Baano 15-01 Rail Jack, 10t/7t Capacity; (1) Simple 2.1/2 x 18, 23" High, 24 Tonne Jack. Approved Contractor for this Lot is Partner Serwis, Piotr Sinkiewicz, Tel: 600 051 239, piotr.sinkiewicz@grupapartner.pl If you are the winner of this Lot, please contact Piotr Sinkiewicz for a removal quotation. - LOT 298
![site]()
Spare parts for FYN-50 Machine
This lot contains: 5 x CLUTCH SLEEVE 84030-FYN50; 1 x TOOTHED BELT H 300/150; 1 x VALVE UZCP-10-52/100-W-2; 1 x POWER SUPPLY DMW-0016/EJ331 400V 16A /APATOR CONTROL; 1 x LAMP ON-1/1-BL 75W 230V; 1 x TOOLFLEX M16 CLUTCH - DOSTAR; 1 x COUNTERWEIGHT RELIEF VALVE; 1 x SMZ41-9.525 Bellows Clutch - LOT 299
![site]()
Spare Parts for HURON Machine
This lot contains: 1 x MMS-2X MEASURING HEAD; 2 x WL4-2F331 SENSOR; 3 x SOLENOID VALVE 5470; 31 x SPRING d=1.2/ Dw=4.5 according to the formula; 4 x HYDRAULIC FILTER FH25/63M25S; 1 x PUMP HPPZ1-2.7-E-1-P-44-CC-N; 1 x SWITCHING VALVE WH-ANe1-1; 4 x FILTER CARTRIDGE WH32-63-25SX; 4 x FAN QL4/2000-2212 24VDC; 1 x 1m CABLE 6FX8002-5DS31-1BF0 MOTION-CONNECT 800Plus 4G2.5+1P1.5C-C 15m /SIEMENS; 1 x PRESSURE VALVE DA 6 VP2B5X/200FSM; 8 x BEARING 51106; 5 x CINTROPUR NW25 FILTER CARTRIDGE; 0.9 x FILTER NET; Set of 10 ROLLER KRV19-PP-A IN; 3 x FILTER INSERT P10-G00-5-M; 1 x BMF 305K-R-US-L-3-03 SENSOR; 1 x PUMP 0510010313; 1 x JOINT ROTO GLYD RUNG D.150; Set of SMC VALVE 3/2, NC, 24VDC VP342. - LOT 300
![site]()
Spare parts for HURON Machine
This lot comprises of 1 x PRESSURE SHUT-OFF VALVE; 1 set of MEASURING RULE LS487C 720mm; 1 x INDUCTIVE SWITCH BNS 816-B04-P; 3 x SENSOR (0830100368) AVENTICS; 1 x SENSOR HOLDER (W0950000125); 1 x ELECTROMAGNETIC LOCK AZM161SK-12/12; 1 x AZM 161-B1E LOCK KEY; 2 x TLK-38-LERR PID CONTROLLER; 1 x SENSOR IFRM06P1701/KS35PL; 1 set of PNEUMATIC ACTUATOR DNM025.0100 /PNEUMAT; 1 x STRAIGHT TIP SNS/025-032 /PNEUMATIC; 2 x Conical silencer SA-G1/8"; 1 x CLS6-C4/3-DP OVERCURRENT CIRCUIT BREAKER /MOELLER; 1 x TIME RELAY LA3D22A65 0.1-30s /TELEMECANIQUE; 1 x Z AXLE CLUTCH D.38/32; 2 x AUXILIARY CONTACT 760021.0000 /LUETZE; 2 x PLUG 2506-00 ID NO. 008353; 2 x BC FORCE MOUNT (1827020084); 2 x BEARING HK2212-B; 1 set of PNOZ X7 RELAY 24V AC/DC /PILZ; 1 x WST3206 OIL FILTER. - LOT 302
![site]()
Spare parts for HURON LEHMANN
This lot comprises of: 3 x PULLEY 28-AT5/74-2; 1 x AUGER EXTENSION 420.0665.a; 2 x BEARING AXK130170-A; 2 x RING 430-0021b; 7 x BEARING K25X30X20-B; 3 x BEARING FLANGE 430-1188; 5 x BEARING RING 171-0006b; 2 x COVER 430-0665; 3 x SIMMERING 50x65x7; 1 x INA BEARING K130x137x24-A; 2 x INA AXK 130170-A BEARING; 2 x KALISZ SNAIL; 2 x LEFT SCREW COVER; 1 x RING 130/170x9 WS81126 17; 1 x BEARING HOUSING 430-1187; 2 x RING RLK 350 19X35; 2 x REFERENCE RING 430-0412c; 17 x SIMMERING 28X40X7; 1 x TOOTHED BELT AT5 1050/20; 5 x O-RING 250. - LOT 305
![site]()
Spare parts for NX155 Machine
This lot comprises of: 3 x HYDRAULIC HOSE DN06 1SN L1300; 2 x HYDRAULIC HOSE DN06 1SN L1200; 2 x PRESSURE TRANSMITTER 10-100BAR; 5 x STRIP BRUSH type SPZ 7/9 +; 1 x CONNECTOR BODY; 1 x ROLL-UP COVER UNDER THE BOTTOM BRACKET; 2 x SEAL GMN M 100X120X10; 1 x TIE ROD L395.5; 6 x "BREATHER 1/2"" 4358-8.6.7."; 1 x MEASUREMENT TRANSDUCER CLUTCH; 6 x SEALANT LN-25X33X4. - LOT 306
![site]()
Spare parts for NX155 Y Axle
This lot comprises of: 1 x ROLLER COVER L= 700 x 2000 Y AXIS and 1 x PANTOGRAPH GUARD 260x1350x260 L=600/800 Y AXIS - LOT 33C
![site]()
2 Master Climate B15 EPB 15kW Electric Fan Heater
Air Flow Rate 1,700m³/h. Voltage 400V. (2022). - LOT 3H
![site]()
Technical Sand Mixer Unit with Control & Hopper
Approved Contractor for this Lot is Pieco-Budow, Maria Paluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 6B
![site]()
Pieco Serwis Gas Furnace 'H' With Control & Loading Bogey
With Movable Bottom (H) Automatic Control With Computer Visualisation. Load Capacity 100 Ton, Hearth Length 9.5m, Gate Clearance Width 7.5m, Height 5m, Maximum Temperature 1,150° C. Temperature. Approved Contractor for this Lot is Pieco-Budow, Maria Paluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 6D
![site]()
Pieco Serwis Gas Furnaces 'D' & 'F' With Control & Loading Bogeys
With Movable Bottom (B) Automatic Control With Computer Visualisation. Load Capacity 25 & 32 Ton, Hearth Length 4.7 & 5.3m, Gate Clearance Width 3.7 & 4.7m, Height 3.2 & 3.2m, Temperature 1,100° C & 1,150° C Temperature Dispersion ±10° C. With Extraction. Pieco-Budow, Maria Paluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 4B
![site]()
Kemper Welding Dust Extraction Unit Series Weldfil
Extraction Capacity Min 18,500m2, Max 26,640m2. 22kW Motor. With Quantity Of Spare Filters. S/No. 210900223 (2021). Approved Contractor for this Lot is Pieco-Budow, Maria Pauluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 301
![site]()
- LOT 6E
![site]()
Pieco Serwis Gas Furnace 'C' With Control & Loading Bogey
With Movable Bottom (B) Automatic Control With Computer Visualisation. Load Capacity 20 Ton, Hearth Length 4.7m, Gate Clearance Width 3.2m, Height 2.3m, Temperature 1,100° C. Temperature Dispersion ±10° C. With Extraction. Pieco-Budow, Maria Paluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 6G
![site]()
Pieco Serwis Gas Furnace 'B' With Control & Loading Bogey
With Movable Bottom (B) Automatic Control With Computer Visualisation. Load Capacity 110 Ton, Hearth Length 11m, Gate Clearance Width 7.5m, Height 4m, Temperature 1,100° C. Temperature Dispersion ±10° C. With Extraction. Pieco-Budow, Maria Paluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl If you are the winner of this Lot, please contact Maria Paluszek for a removal quotation. - LOT 307
![site]()
Spare parts for HURON LEHMANN
This lot comprises of: 3 x SIMMERING 25x33x6; 3 x QUADRING 430-0603; 3 x QUADRING 430-0604; 1 x SIMMERING 30x37x4; 3 x CLAMPEX CLUTCH KTR 105-32X55; 1 x BEARING HOUSING 430-1187; 1 x WORM BEARING CLAMP COVER; 1 x BEARING COVER 430-1187/88; 2 x CLAMPEX CLUTCH KTR 105-20X38; 5 x BEARING K30X35X13-B0-2; 9 x SIMMERING 50x65x7 TC; 1 x HAN K4/8-F-s INSERT 09380122701; 1 x SOCKET HOUSING HAN09300240520; 1 x PULLEY 28AT5/74-2 SBF; 2 x ACTUATOR 410.6.032a (after repair).
Essential Information
General Information
- Auction Dates
- Starts: 26 November 2025 at 14:00 GMTEnds: 15 January 2026 at 14:00 GMT
- Site Address
- Stoczniowa 2Warmian-Masuria82-300Poland
- Viewing Days
- By Appointment OnlyViewings strictly by appointment only – Please contact Apex to make an appointment.
Fees & Payment
- Currency
- EUR
- Buyers Premium
- 18% or as specified on individual items
- Payment
General payment information
- Payment is due immediately on receipt of invoice.
- All payments must be made in the currency on the invoice issued.
- Accepted forms of payment are bank transfer ONLY. We do NOT accept payment by card, cash or cheque.
Goods
- Clearance days
- 25 January 2026 at 08:00 GMT - 27 February 2026 at 15:00 GMTCollections strictly by appointment only.
- General Collection Information
Collection
Only GE Approved contractors can be used on site
Any Bidder MUST and CAN ONLY USE the GE-Approved Contractors to Work Onsite, which currently are:
In charge of entire site:
Jarosław Błaszczuk, Site contact, Tel: 48 601770160. Jaroslaw.Blaszczuk@gevernova.com
Contrators responsible for different lots, please check each lot for correct Contractor:
Partner Serwis, Piotr Sinkiewicz, Tel: 600 051 239, piotr.sinkiewicz@grupapartner.pl
Pieco-Budow, Maria Pauluszek, Tel: 48 502 549 969, piecobudowa-elblag@wp.pl
Promxmus, Artur Azborowski, Tel: 539 629 111, a.zaborowski@proxmus.com
- Buyers are fully responsible for removal of items plus all shipping and rigging charges.
- Items are only available to collect once the transfered funds have cleared, and a collection appointment has been booked.
- Buyers or third party movers must present an invoice to the on-site personnel when removing their items.
- Buyers must complete the removal of items within the clearance deadline. Normal removal hours are Monday to Friday, from 9am to 4pm (local time) unless otherwise stated.
- Contact and removal information will be emailed at the time invoices are issued.
- Sales Contacts
- Auction informationKarla Swain69 Middle Street
Brighton
BN1 1AL
United Kingdom info@apexauctions.co.uk+44 1273 224466